SNX SYSTEM 2 G3 CONTOUR EDGEBANDER
Stock Number:
12688
Condition:
CLEANED/CHECKED
Electrical:
230V, 3 Ph, 60 Cy
FOB:
Sanford, NC
Replacement Cost:
~$85,000
Our Price:
$49,500
Freight Charges Not Included
Main Machine Features:
- Non-stop operation utilizing twin vacuum arms and 3 workstations
- Large touch screen controller
- Large heavy duty movable vacuum pod arms for ease of operation (max panel weight 230 lbs.)
- Triax 3-Axis laser system to insure consistently tight butt joints on panels
- Designed to apply hot melt EVA adhesive and edgebanding from .5 to 3 mm
- Trimming unit to facilitate trimming of the top and bottom overhang of the edgebanding
- Armordrive Kevlar lower belt drive system for smooth, quiet, long life operation - no lubrication
Digital Control Features:
- Digital control: Ability to program length/electronic encoder, cut off point for guillotine
- Ability to select laser measurement to assist encoder for more accurate splicing of joints
- Temperature on/off (separate temperature thermostat to adjust adhesive temperatures
- Screen with graphic interface makes programming easy
- Ability to select manual or semi-automatic function
- Variable speed manual adjustment
Twin Workpiece Holding Mechanism Features:
- Utilizes a pneumatic vacuum pump system
- Vacuum is provided via a rotating vacuum pod table
- Additional vacuum tables are available but not included (part specific)
- Work piece feeder is driven with an extra wide rubber roller and double upper support rollers
- Vacuum table are at the end of a large heavy duty articulating arm
Edge Coil Magazine Features:
- (1) universal magazine rotating table for coiled material
- automatic guillotine for coiled material up to 3 mm x 45 mm
- Guillotine is activated by a digital/laser encoder reader or by manual foot operation
- Self engaging Triax 3-axis laser system allows accurated reading of the contour of the panel and of panels with slight warping or sagging
Gluing Station Features:
- Glue pot with 1 Kg. capacity
- 10 to 60 mm work piece capacity (note: work piece thickness is dependent upon edge tape thickness)
- Glue tank made from aluminum for easy heat dissipation and cleaning
- Digital glue temperature settings
- Dual rollers to copy the shape/contour of the parts being banded
Top and Bottoom Trim Station Features:
- (2) .75 hp 12,000 rpm high frequency motors for edge trimming
- Vertical and horizontal tracing via roller transer rollers and pad
- Maximum edge strip thickness 3 mm (up to 45 mm panel thickness)
- Maximum edge strip height: 60 mm
- Radius capability up to 3 mm radius
- Manual adjustment of the trim motors for workpiece thickness via hand lever
- Pneumatic opening of the trim motors fo facilitate the introduction of the panel
- Guiding and positioning of the trimming function around the contour of the panel is done manually by the operator
- Pneumatic exclusion of the trim unit via auto switch
- (2) cutterheads with stepped radius cutters of 1,2, and 3 mm
- "Rapidset Copy Shoe Turret" easily switch from 1,2, or 3 mm banding
Working Dimensions:
Edge coil thickness: .5 to 3 mm (.5 mm thin tape ONLY with proper low temp adhesive)
- Work piece min: 150 mm diameter
- Work piece max: 2400 x 2400 mm
- Work piece thickness: 1- to 60 mm
- Edgeband thickness: .5 mm to 1 mm for panels up to 60 mm thick
2 mm for panels up to 60 mm thick
3 mm for panels up to 45 mm thick
- Minimum outside radius: 30 mm(note: based on 1 mm thickness of banding
- Minimum inside radius: 150 mm
- Feed speed (rotation): 16 fpm
- Air requirements: 6 bar (90 psi)
- Electrical requirements: 10 amps@ 230 Volt 3 phase
- Footprint required: 19' x 10'8"
- Note: includes (2) optional 48" x 16" vacuum tables and (1) 96" x 18" vacuum table